Heltec Wifi Lora Kit 32 V2 868 - 915 mhz 0.96 inç Oled
|
1 |
CE Certificate; |
|
2 |
Microprocessor: ESP32 (dual-core 32-bit MCU + ULP core), with LoRa node chip SX1276/SX1278; |
|
3 |
Micro USB interface with complete voltage regulator, ESD protection, short circuit protection, RF shielding and other protection measures; |
|
4 |
Onboard SH1.25-2 battery interface, integrated lithium battery management system (charge and discharge management, overcharge protection, battery power detection, USB / battery power automatic switching); |
|
5 |
Integrated WiFi, LoRa, Bluetooth three network connections, on-board Wi-Fi, Bluetooth dedicated 2.4GHz metal 3D antenna, reserved IPEX (U.FL) interface for LoRa use; |
|
6 |
On-board 0.96-inch 128*64 dot matrix OLED display, which can be used to display debugging information, battery power and other information; |
|
7 |
Integrated CP2102 USB to serial port chip, convenient for program downloading, debugging information printing; |
|
8 |
Support the Arduino development environment; |
|
9 |
(Exclusive) Supports the Arduino version of the ESP32 + LoRaWAN protocol routine provided by Heltec. This is a standard LoRaWAN protocol that can communicate with any gateway/base station running the LoRaWAN protocol (requires serial number activation, only the development of the company) The board is available) |
|
10 |
With good RF circuit design and basic low-power design (sleep current ≤800uA), it is convenient for IoT application vendors to quickly verify solutions and deploy applications; |
Technical Parameters
|
Source |
Parameter |
|
MCU |
ESP32( 240MHz Tensilica LX6 dual-core + 1 ULP, 600 DMIPS, 520KB SRAM, Wi-Fi, dual mode Bluetooth) |
|
LoRa chip |
SX1278 |
|
LoRa bands |
EU_433, CN_470_510, EU_863_870, US_902_928 four bands optional |
|
LoRa maximum output power |
18dB ± 2dB |
|
Hardware resources |
UART x 3; SPI x 2; I2C x 2; I2S x 1 |
|
|
12 – bits ADC; 8 – bits DAC |
|
|
29 general GPIO |
|
Display |
0.96 inch 128*64 OLED display |
|
FLASH |
4MB(32M-bits) SPI FLASH |
|
interface |
Micro USB x 1; LoRa antenna interface(IPEX) x 1 |
|
Size |
50.2 x 25.5 x 9.74 mm |
|
USB to UART Bridge |
CP2102 |
|
Battery Type |
3.7V Lithium(SH1.25 x 2) |
|
Battery detection circuit |
√ |
|
External device power control(Vext) |
√ |
|
Low power design |
Deep Sleep 800uA |
Eletrical characteristics
|
Electrical characteristics |
condition |
Minimum |
Typical |
Maximum |
|
Power Supply |
USB powered(≥500mA) |
4.7V |
5V |
6V |
|
Lithium powered(≥250mA) |
3.3V |
3.7V |
4.2V |
|
|
3.3V(pin)powered(≥150mA) |
2.7V |
3.3V |
3.5V |
|
|
5V(pin)powered(≥500mA) |
4.7V |
5V |
6V |
|
|
Power consumption(mA) |
WIFI scan |
|
115mA |
|
|
WIFI AP |
135mA |
|||
|
LoRa 10dB emission |
50mA |
|||
|
LoRa 12dB emission |
60mA |
|||
|
LoRa 15dB emission |
110mA |
|||
|
LoRa 20dB emission |
130mA |
|||
|
Output |
3.3V pin output |
|
|
500mA |
|
5V pin output (USB powered only) |
|
Equal to input current |
|
|
|
External device power control (Vext 3.3V) |
|
350mA |
Package Include :
